E21: Steering Wheel Retrofit Guide

I got asked on eBay UK if my E21 steering wheel would actually fit an E30, which it turns out they don't. The wheel was then snapped up by someone with an early '70s 2002, but only after I could convince them it would fit...

It's not straight forward, so to clarify...

Later E30/E36/E46 3-Ser / E28/E34/E39 5-Ser / E24 6-Ser Etc. Steering-Wheel to E21 + other Classic BMW:

To fit later model steering-wheels with the modern spline to your E21 or other pre-'82 BMW, then you will need a steering 'boss' adapter, which bolts to the steering-column and usually has multiple sets of bolt-holes to accept any after-market steering-wheel. Some may only have holes to fit the brand of steering-wheel that make the hub, such as the MOMO one, here for about £60, but could be easily adapted to fit whatever wheel you have. Getting a universal one is harder, sites like meanmachines.biz claim to have ones here for £25 that fit, but they may need adapting to go on the E21.

Earlier E6 [1602/2002] / E12 5-Ser Steering-Wheel to E21:

Not sure why you want the thin, bendy rim of the older model steering-wheels to noon your E21 around, but they are a straight fit and require no modification to the wheel or dash/trim. The horn contact ring at the back needs modifying to work - refer to step 3 of the guide below.


E21 Steering-Wheel to E6 [1602/2002] and E12 5-Ser:

This is a common mod and it makes sense to upgrade 60s and 70s BMWs with the old-style steering wheels to E21 types - they're newer in design, better to use and safer in an accident. E21 wheels are a straight fit to the spline, but some cutting it required to the dash or back of the wheel to get it to fit. The horn button-contact at the back also needs modification.The definitive guide on tidily retrofitting E21 wheels to 2002 etc. is on the 'Bay Area '02' club site- http://www.bayarea02.com/techtips/320_wheel/index.html

The are highlights taken from the bayarea02 guide:
Spline Fitment:
If you place the 320i 4-spoke steering wheel onto the '02 steering column, you'll find that the bottom portion of the steering wheel interferes with the padding on the steering column by about a 1/4 inch. Grab a sharp utility knife and carefully trim away the bottom of the steering wheel, or install some sort of 1/4-inch thick spacer between the steering wheel and the steering column.

If you choose the spacer approach, you have to make your own spacer, as commercial flat washers are too large. The spacer needs to have an inner diameter of about 5/8 inch and can be no larger than 1 inch. When I installed a 320is steering wheel into my '02, I made the spacer out of a piece of 1/8-inch diameter aluminum rod and bent it into a ring using one of the sockets from my toolbox as a mandrel.

One cautionary note about the use of a spacer: The lock nut might not grip the shaft threads if the spacer is too thick. Losing a steering wheel in mid-apex is BAD!

Horn Buttons:

Take a sharp utility knife, and make a radial cut completely through the brass ring on the 320i steering wheel. Once the ring is split, use pliers to carefully bend up one end of the ring high enough to form a cantilever leaf spring. Then bend the tip of the ring over to form a smooth contact surface for the steering column.

This method works well with the standard 4-spoke 320i steering wheel because there is little, if any, access to the internal wires going to the horn buttons.

The classic BMW parts market is a lucrative one, as I will detail my own exploits in another post. I assumed E30 steering-wheels where fair game for the E21 and at the time I listed mine the going rate for an E30 foam-plastic wheel was £30. I got £50 for my original E21 wheel, but I wonder if I could have got more. Due to the scarcity of E21s, I would estimate the value of the basic 4-spoke steering-wheels at minimum £50. The 3-spoke 'sport' wheel in foam-plastic is even more sought after and should fetch up to £100 in good condition and at least £100 for a leather-bound one. The wheel fitted to me E21 was a period AC Schnitzer 3-spoke leather wheel with a removable centre. The boss-adapter and condition of the wheel led me to believe this had been pulled from an E30, though I've never seen another like it and wish I'd put the original one back on to sell the car.

E21: Seat Fitment Guide:

Swapping seats round in a BMW E21 3-series is a nightmare, thanks to the floor-mounts being two different heights. To fit level-based seats from another car requires chopping out the welded floor-mounts and once this is done there is no going back.

1. Check if your floor-mounts have been chopped:

Check the outer floor-mounts on either side, spot-welded in place just inside the door-sill. They should look the one in the left photo below.

If they don't, and they look more like the right photo [with or without the wood], then you have chopped mounts and seats not originally from an E21. You also won't be going back to E21 seats very easily, so to preserve the style and make the ride a lot better, throw in seats from a newer BMW.

2.1 Fitting stock BMW seats from E30, E36 etc. :

This makes sense. E21 seats are sprung and uncomfortable and were dropped in almost every succeeding model. Other BMW seats are easier to come by and cheaper. E30 seats preserve the look almost identically and are far superior in construct. They also fit the inner seat mounts on the E21, the ones against the trans.-tunnel, so only the only outer ones need adapting. I am sure this is the case with seats from other 80s BMWs, possibly the E36 and E46 as I've seen it done, but need confirmation.
Modifying the outer floor-mounts, the ones against the door sills, is impossible as they just sit that much higher than the inner ones, the E21 of course having a crazy odd-height sub-frame design, so they need cutting out. Putting in new ones is pretty straight forward though, you can fabricate them with steel or alloy C-channel, wooden blocks, improvised stilts - these are all popular methods. Tilt-forward seats don't tend to be very strong anyway, so the new mounts don't have to be rock solid as long as they're bolted or welded securely to the floor-pan. Mine used the stock inner floor-mounts and a wooden block on the outer side to get the height - this presented no problem to the UK MOT (roadworthiness-test).

Check out my guide here: http://e21dub.blogspot.co.uk/2013/09/e30-sports-seats-fitted.html

Or check out HSVTurbo's guide HERE [where I got my idea] in THIS THREAD on bimmerforums.

2.2 Fitting rigid Racing bucket-seats:

If you're building a track car then it's obviously best to keep things as stiff and secure as possible. The neatest and most weight-saving method is to cut some steel cross-beams to fit and weld them across the floor-pan, from the trans.-tunnel to the door-sill. This could be done with or without removing the outer floor-mount, but you will probably have to do this to get the seat low enough. Two cross-beams under each seat would probably be best, but it is most often done with just reasonably thick one.

More info. HERE on bimmerforums.

2.3 Fitting non-BMW stock seats (VW, Ford Recaro etc.) :

To get the right height and a central-position with stock seats from non-BMWs there is a lot of modification to the mounts - these seats will always have the bolt-holes in the wrong place. The tidiest way would probably be to weld in rigid cross-beams like in the above guide [2.2], otherwise you will need to fabricate custom mounts. [I used a combination of wood-block and steel cross-beam to fit Ford RS Recaros to mine in THIS POST].

Check out my guide here: http://e21dub.blogspot.co.uk/2013/08/recaro-seat-base-adapter-finally-solved.html

3. Re-fitting stock E21 seats:

I have never seen anyone online do this. If you have level floor-mounts then I see no reason to switch back to E21 seats. All but the Recaros are uncomfortable, sprung nightmares. They give a truly bouncy and uncertain ride - only the most restoration mad would want it. The Recaros are super-rare and overpriced to fit the E21s mounts. E30 Recaros are a fraction of the price, have level mounts and are better anyway. If you are so desperate to restore your E21 dutifully, then I would consider it having cut floor-mounts a deal-breaker and to find one with stock seats, because the car will never be the same again.

There are 3 ways I see to achieve refitting stock seats:

1. Build custom outer mounts using a combination of the methods above, building them back up to the original and rather tall height for the stock seat-frames. [].

2. Locate a pair of original outer floor-mounts that have been cut out of another E21 and refit them to yours. These would first need to have been cut out carefully from the donor car and preserved by someone. Whether they would advertise them for sale is another matter, but asking on the forums can't hurt. Otherwise, you'll need to find someone with a scrap / breaking E21 and ask to neatly cut out its floor-mounts for a few quid. Either way, obtaining a useable pair is going to be tough.
Once you do though, they would just need to be measured up to where yours were cut off and welded into place. How neat a job you do will determine whether they fit or if it's unnoticeable.

3. Fabricate new outer mounts from the ground up out of steel and weld those in. I will endeavour to make a note of the dimensions of my cut one before passing it on and do a quick CAD design to fab-up a simple one.

**Also, I still have the passenger-side (N/S, Euro/US Driver-side) floor-mount [above], so if anyone wants it to try and weld back in message me! [Sadly, I cut the driver-side one out more severely and this is probably going to be the case if yours are chopped as it gives the wood or whatever more to grab on to.]

E21 316: Car sold...

Met up with Jake yesterday and did the deal. He was getting the train down on his own from Newcastle, so asked if we could meet him in Manchester with it to halve his train fare, which was fair does, it's only about 40 miles from us and was a good chance to see if the car was up for the Newcastle run before handing it over... 

Obviously it was and once I'd hit the M56 I was whipping past cars in the middle-lane with my Dad struggling to keep up in his Audi. Apart from getting a bit warm in the cabin, the engine was ticking along beautifully at about 3,400 revs @ 70mph and I did manage a few stints at 80mph @ around 4,000 rpm, but my right foot was quickly subdued at the sight of a steaming Volvo Amazon on the hard-shoulder - the stranded owner grimaced at me as the Bavarian stalwart roared past, but as we got into Manchester the car was just as sedate in the long traffic-light queues and turning a lot of heads! 

After such a charming run into the city-centre, public-transport showed its true colours and there was bedlam with the Trans-Pennine trains and Jake's arrival was delayed by about 40 minutes. After that the switchover went nice and smoothly, the car speaks for itself and I knew he was keen anyway,so we were back on the road home again in about half an hour with no haggling. I threw in the original 13" steel-wheels, the beige rear seats, the short SPAX springs and a few other bits and bobs including the black rear grille-panel. Jake is only 20 and has had a couple of slammed Mk1 Golfs, so he's well into the scene and I can tell the E21 has gone to the right place, where it will be equally coveted and, hopefully, seen out a bit more.

Of all my car projects, this one was by far the most popular. Bye bye little E21, you will be missed.

Last ever fill up. Took it into work up the motorway for a pre-run check and it was flying.  I threw the 16s on for the trip to Manchester and was expecting a bit of steering-wheel wobble with them not being balanced, but above 50mph the wheel became eerily calm and gave the best high-speed ride so far, even with those stretched tyres.

The highest speed (and most fuel in the tank!) since the day I brought it home from Surrey :)

Parked up in Picadilly station car park, where it drew quite a bit of attention. There were 2 parking-attenants in the place and both were suddenly drawn to it like a magnet, which was unnerving at first.

Timeless lines. Probably the only E21 out in the city that day and getting a lot of love from the Mancs.

The E21 shape just has to have deep-dish wheels - it's well worth the effort to get 9Js on the back.

Coombs of Guildford, endorsed by the Queen no less. Old Beemers famously outlive their dealerships, but I'm pleased to see Coombs is now Vines of Guildford, still a BMW specialist.

In the immortal words of Andy L. - "I do love a sticker". 

E21 316: Last week with the E21...

Quite a sad time this week as the car is now confirmed sold, but it's nice to see it will be going to an enthusiastic new owner, a lad called Jake from Newcastle ways. Quite ironic that the car doesn't leave leafy Surrey for 29 years, then in the subsequent two makes it's way through Liverpool (230 miles away) and then as far North as it practically can to 'Castle (another 175 miles)!

It will be very dearly missed, the handsome E21, not just for the sentimental reasons of it being the exact same age as me or the extent of work and restoration I carried out, but mainly because it is such an awesome car to behold. Time waits for no man and it would be even worse to see me SORN it, hide it away somewhere and let it fade away... it needs to be kept on the road so it can be enjoyed by both the driver and the public. Like any BMW old or new, the thing just loves to be driven and gets better and more rewarding the more you do. It's also great that other people like the shark-nose classic (and in some cases, rare but gratifying, actually get the stance scene :D) and appreciate the work that's gone into the project.

E21 Dub Club has had over 12,000 hits and a heap of good feedback and I would like to thank everyone who has checked it out, not just those who gave props props on the motor, but for those who found it useful and have been helped or inspired with their own E21s... hats off to you. Finally, a big shout out to Clint Warburton for his support - hope with all the space of the Ozzy outback you get to keep your E21 for the foreseeable future.

Never the less, a new project beckons, but sadly it's a bricks-and-mortar style project this time. That time has come again for me to flee the parents nest and give up my natty cars, though I'm sure another retro BMW will appear when the dust settles from this house!

Back in the car gallery at West Wal, where it's not been enough this winter....

Turning heads in Co-Op car park, Wallasey...

Built, not bought. Driven, not garaged. And simply stunning to boot,, even rocking the 15" Melber wheels...

Checking out the bad boy evil Angel Eyes in the tailgate of this Mini. The poor girl must have wondered what I was doing taking photos... obviously she hadn't seen the eyes approaching and got out of the way - it was flying in the cold air!

E21 316: Flared wheel-arches painted.

I have a buyer organised for the car, coming to pick it up next weekend. Just throwing up some recent pics of the painted wheel arches.

E21 316: Update + MOT Pass

After my disastrous few weeks I managed to get hold of a Bilstein strut-insert and get it onto the car along with the longer springs, meaning it was finally back on the road and in an state worthy of the MOT test. I cautiously rolled down to the test-station on Saturday and am glad to say the E21 passed with flying colours!

Bilstein damper is strong, but will be a pain with the short springs.

This was a relief considering the slightly dodgy seat-frames I made bolted through the floor-pan, which stuck out like a sore thumb when it was up on the ramps, along with the scuff marks where I've grounded the underside, but with the car at a more standard height off the ground this didn't see to bother them and there was no problem with the chassis at all.

Oddly, the guy told me that the split-pins were missing from the castle-nuts on my steering track-rod ends and this would actually be a fail under normal circumstances, but they could see I'd been working on it and decided to give me the benefit of the doubt. This was true, I'd had them off swapping the springs and hadn't bothered to replace the split-pins as they would be coming straight off again to put the short springs back. That was decent of them to let it go, as it would have been beyond frustrating to lose another week to something so trivial and shows just what a pain the UK MOT test is.

Folded up and with a 1/4 inch thick layer of
pallet-wrap to send as a parcel.

Spending on the E21 has been a bit out of control since buying the E30 seats and it is still in desperate need of the wheel-arches finishing off. By this point, I'm past what I can recoup if I sell the car. I'm still using my E39 as my daily, the E21 has had no use for nearly a month with no MOT and finally, due to a planned move, it's looking like I will have to let her go anyway, unless I can find somewhere cheap enough to store it. I had hoped to have the arches skimmed off and painted by the guy who did the respray, but money is tight so I will be buying a rattle-can and doing the best I can with them.

Thankfully, I've managed to generate a bit of extra cash to pay for the strut-debacle [this post], by selling some bits on eBay, like a battered old set of alloys, an E36 nose-cone and other bits I had lying around, as well as the original beige passenger seat from the E21 - I think I have enough seats for the car now. I hope the seat arrives to the buyer OK, as I had to practically shrink-wrap it to be able to send it Parcelforce [£27], pictured, as the original method of courier was just over £60!

My spare set of E21 ash-trays is not selling on the other hand and is still on the site here - http://www.ebay.co.uk/itm/181235987123.

E21: Deep 'Alpina' Style Front Valance on eBay UK

** UPDATE - This sold for the same £51 bid that was there on day one of the auction, but alas I missed the end.

I've been looking for a replacement chrome rear-bumper to get rid of the two minor, but ugly, dents on mine and spotted this -

http://www.ebay.co.uk/itm/121179262087?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2649

A super-rare for the UK deep front-valance / bumper, I think from the 'Alpina' models and it's genuine BMW. Probably going to sell for way over the current £50 bid, but I think I will be having a cheeky bid myself if it doesn't go stratospheric.

E21: Front indicators - a common problem?

Is your front corner-indicator not working, but the bulb and fuse are fine?

Mine wasn't and it turned out to be the metal live-clip that sits against the bottom of the bulb. Not the best of designs, connection is lost to the bulb if the clip is bent back slightly, causing the indicator to fail intermittently [denoted by faster clicking of the turning-signal]. The clip having a little corrosion or crud on it is also enough to stop the bulb getting a signal.

A quick clean up with emery-cloth and a slight bend forwards so it sits tight on the bulb was enough to get mine working solidly again. This could be a common problem, especially in the UK and Europe where grime gets pushed everywhere in an E21, so if your fuse and bulb appear fine, but the indicator won't work, you can bet it's the live-clip.

PROCESS:

1. Dis-connect the corner indicator wiring by sliding apart the plastic-clip located behind the headlamp under the bonnet and push it through the hole to the outside of the wing.

2. Remove the two crosshead screws holding the corner-indicator lens and lift the lens off.

3. Remove the two crosshead screws holding the indicator-housing to the wing. The housing should now slide forwards and clear the wing.

4. Use nose-pliers to remove the metal live-clip from where it sits in the plastic-housing.

5. Bend the prong [denoted by the arrow] in towards the other prong, bringing the flat-edge down.

6. Clean up the face of the prong and the metal-contact on the bulb with emery-cloth.

7. Replace the live-clip to the plastic-housing and reverse Steps 1-3 to re-fit.

E21 316: Burst shock-absorber woes...

SPAX adjustable - like hen's teeth.

Well, I've had a bit of a nightmare week. As I was replacing the front n/s shock-absorber with the new spring, ready for the MOT on Saturday, the strut-insert burst in my face. To get an extra couple of inches clearance at the top and get it under the wing I'd been pushing the damper down into the insert. I figured they sit quite far down with the short-springs anyway, but eventually, probably after doing it several times, I must have plunged it further than its full operating depth and it popped, sinking the insert completely into the strut.

You wouldn't think pushing it down would pop it, considering the forces on it under load, but once its down far enough the top seal just fails under the pressure of the oil. You can have SPAX, as with most adjustable-inserts, re-filled and the seal replaced if you can be bothered to send it back to the manufacturer and pay the cost, but with time of the essence I just bought a new one.

Larkspeed in Leeds were the cheapest, though the price had gone up from £90 to £112 [and £118 now for the shortened!] for a single insert, but they claimed to have the part in stock and would have it to me by Tuesday the latest. Today I rang them to say it'd been a full week since they rang to confirm the order and still no insert. After half an hour they rang me back to say the insert had been specially ordered from SPAX, who were now lacking correct parts and can't build them until the end of October. I wish they had told me that last week as I'm now waiting on a refund...

Bilstein - fixed damping-rate and pricey,
nothing but good reviews.

I rang DC Performance.co.uk, who also claimed to have the part in stock and it would take 2 or 3 days. Before parting with any money this time I asked if they could check the insert is definitely in stock, which they are not, so it's not looking hopeful for any existing stock anywhere. I will be contacting SPAX directly from now on.

Monroe Gas-Matic - strong, but ride too soft.

So what are the short-term options? There are no ride-adjustable inserts in stock and available now, so it looks like i'm now bound to non-adjustable inserts. Stiffened Bilstein inserts are £62 each, where OEM-replacement ones can be had for as little as £20. With the springs this low, I have no idea what would work best. The sportier, better-brand damper might last longer under the stress and be a better match for the adjustable SPAX on the other side. Alternatively, the cheap, softer damper might compress better under the load and a pair will only cost £40 should the o/s one need swapping too. Another option is to replace both with Monroe gas-filled dampers for £123. The blurb says they are a heavy-duty design for trucks and vans, but according to this thread they are just too soft and will cause me to bottom out. So, £60 for one Bilstein it is, or take a chance on a cheap KYB. Hmmm, stress.

E21 316: Taller springs for MOT.

Well my MOT, the UK roadworthiness test, has come round and the E21 is just too low to get into my local testing station, let alone up onto the ramps. This is where height-adjustble coilovers would be worth their £650, as even if I can get the car onto the ramps, an attempt to raise the wheels off the ground will cause the short springs to become loose in the pans. The solution to this problem is still cheaper than coilovers - shortened strut-inserts from this post at ~£400, but I'll still have to find somewhere with ramps low enough to take her.

Seems to me the easiest and cheapest overall solution is to just swap longer springs in for the test and put the chopped ones back on later. Seems like quite a lot of effort just for a 30-minute inspection, but that's motoring in the UK, we're at the mercy of the MOT and it sees more cool cars off our overcrowded roads than insurance write-offs ever would.

Slight length difference. The red SPAX was a -40mm too.

A nice set of yellow APEX -40mm springs set me back just £80 from eBay. They are a lot longer than I remember though, which heralded me finally buying some spring-compressors, £17.99 and bringing the grand total of this years test to a ton before I've even had it inspected... not good.

Fitting the rear springs was a doddle, but the fronts threw up a few problems. Getting the cut spring off was easy enough, but even under compression the longer one was never going to fit in the space available. After damaging my newly filled wheel-arch and bursting one of my strut-inserts - nightmare - I started looking for a better guide on replacing springs and find out if it can ever be done with the strut and brake-line still attached, but one doesn't seem to exist - a good validation for this and other blogs! I did, however, find a Youtube video of some guys fitting H&R springs without removing the shock, which did give some clues from about 3min30 onwards:

PROCESS:

Rear Springs - 

1. Follow the steps in THIS POST to remove and re-fit the rear shock-absorbers, swapping the cut-spring for the new ones, obviously.

Front Springs [without removing strut, steering or brake-line] -

1. Raise the car and remove the corresponding front wheel. [It makes life easier to drop the front on axle-stands and remove both wheels, doing both springs together.]

2. Undo the top-nut from the shock-absorber, located on the suspension turret under the bonnet, using a 19mm wrench and 8mm open-end spanner at the top of the strut-insert to stop it from rotating.

3. Disconnect the brake-pad sensor wire by simply pulling it apart at the join behind the disc and sliding the rubber-mount free of the bracket.

4. Remove the earth-lead from the strut by undoing the bolt with a 10mm wrench.

5. Remove the bracket holding the brake-line to the strut using a 10mm wrench and open-end spanner. [This is essential to free the brake-line enough for it to tilt forward without having to remove the hose and drain the brakes. Without freeing the bracket, the brake-line will be stretched to breaking.]

** If the spring is still under compression without the weight of the car on it, use spring-compressors to hold it short enough to loosen the top spring-pan away from the turret.

*** The strut can be tilted out far easier with the track-rods unbolted, using a 17mm wrench and moved out of the way, but mine wasn't budging easily and there is enough room if you can push the steering-arm down enough.

6. Remove the four nuts holding the anti-roll bar brackets to the sub-frame using a 17mm wrench and open-end spanner. The anti-roll bar should drop down and remove tension from the two struts.

7. Tilt the shock-absorber strut out of the wheel-arch, remove the top spring-pan and spring.

8. Drop the new spring onto the bottom pan and reverse the above steps, using spring compressors if necessary.

Wheel-arch gap a little more prominent. Was it really that much before?!

E21/E30: Crude Rear Seat Repair.

When the seats arrived the rear one had a noticeably big tear on the top of the back-rest. By the time I'd finished cleaning them however, there were now 3 tears along the same strip. I was being super-careful with the scrubbing brush, but after 25 years under the back-window the glue is coming away and the strands of twill fabric separate very easily indeed. An attempt to repair one of the splits only made it worse as the material is stretched by the glue and can't wait to rip.

I considered throwing the stock beige seats back in, but then had a moment of er, inspiration, and found a strip of spare material wedged into the frame behind. I cut it into patches and stuck them down with fabric spray-adhesive, £7.99 but it's strong stuff.

It's not the prettiest of repairs, despite matching the lines up, but looks better than threadbare, won't get any worse now and the interior of the car looks a lot fresher with them in I must say. If they're going to stay though, a permanent cover-up will be needed - probably in the form of a parcel-shelf re-trim. The beige carpet could do with a refresh, so I may extend the fabric past the shelf and have it cascade over the back-rest slightly. We will see.

E21 316: Fitting E30 rear sport-seats - or having a go anyway.

Stock fit works, but leaves big gaps.

As with the front seats I used HSVTurbos build [here] as a rough guide. His rear bench-seat is the all-sponge kind, whereas mine have the sponge base, but a sprung back-rest, possibly due to the folding arm-rest or model year difference. This means I have a metal frame to work with on the back-rest, so it can be pressed flat to greatly reduce the proud fit at either corner, but also means more needs to be cut away than just blobs of sponge. The E30 coupe's rear seat-pan, the body-tub and front doors are almost identical dimensions to the E21, so the rear seat-base just slots in. There are no brackets along the bottom-edge to clamp the squab down, but with it seated flat and wedged under the back-rest these may not be necessary, although fabbing some up might be worthwhile to stop the carpet sagging down in the footwells.

The general shape of the back-rest is more or less the same as the E21 and the hooks fit into the existing brackets, though the E30's parcel-shelf is curvier, causing the back-rest to stick out slightly at the top corners. The back-rest also sits slightly higher, leaving an inch gap at the bottom between it and the squab. If these gaps don't bother you then the seat works fine like this and will only need a little chopping off each upper corner to achieve a pretty good looking fit. If they do, then a little more work is required to seat the back-rest flush and minimise the corner gaps.

The main problem here are the seat-belt reels, which protrude from the bulkhead and fill up where the upper corners of the back-rest want to be. The back-rest bolsters are also slightly too broad, though the centre of the rear frame is more or less a perfect fit to the E21 bulkhead.

Modifying the Back-rest:

1. Bend up the small hooks holding the cover material in place over each side edge of the back-rest and pull the fabric clear of the metal frame.

2. Cut away the side-support on each side of the frame, leaving just the edge of the 'mattress' frame that holds the springs, as in the photo below. The brackets at each bottom corner should come away here too.

3. Cut in half the metal bar that runs between the centre and bolsters, the one attached to the top spring in each corner, and trim away the top spring as close to the frame as possible.

4. Cut the metal bar running along the top of the frame about 4" in from either top corner

5. Cut away the boar-hair matting along each side of the back-rest to reduce its depth by about half.

6. Cut a 2" square from each top corner of the boar-hair matting to give a recess where the seat-belt can run freely back into its reel.

7. Replace the fabric cover, hooking it to points on the mattress-frame and tucking it under the springs. At each top corner, I pierced a hole and ran a cable-tie through to hold the folded fabric clear of the seat-belt reel.

Fitting to the E21:

To get the back-rest sitting flush to the seat-base the original mounting-brackets may have to be abandoned in favour of slotting the hooks on the bulkhead directly into the top of the back-rest frame. The original lower brackets are attached to the frame here and may need cutting off for a tight fit.

1. Hook the top lip of the back-rest frame over the metal hooks on the bulkhead. Press hard to make sure the metal bar gets over the hooks and not just the boar-hair and fabric. Give each side a good knock down onto the hooks. The top of the back-rest should be about 5mm lower than the parcel shelf.

2. Fit the centre arm-rest and lock the clips into place. The back-rest should sit a bit proud of the bulkhead and need pushing flat. Drill two holes through the back plate of the arm-rest and bulkhead. Fasten it together with two bolts or pop-rivets. Not only will this hold the seat in place, it will also stop it moving when the arm-rest is lowered.

E21 316: E30 Sports Seats - fitted.

MJNewbs from eBay got back in touch and we finally negotiated a low enough price for the seats. The fronts are in great nick, only a slight fray to the driver's back-rest, but the rear seat back-rest has a few tear that I'll address in a later post.

Thankfully, the E30 seat bases fit onto the inner stock mount, next to the trans. tunnel, on the E21 so they are already sited neatly in the centre and only require the outer mount to be lowered. Here's how I finally got them to an equal height.

The outer seat-mount was cut away about 1.5 inches height from the lowest point of the floor-pan and the top half completely removed from the sill. This leaves a large flat T-piece section onto which a length of '2by4' style wood-beam was placed that sits at the same height as the inner seat-mount, give or take 2mm.

To strengthen the edge of the wood where the seat sits a piece of 2mm-thick angle-steel was screwed in place, clamping the wood to the remaining edge of the cut seat-mount. The M10 seat bolts run through the wood and are bolted to the floor-pan, so the wood only acts as a riser, not an anchor and the angle-steel helps to distribute any downward force on the wood, or twisting motion as the seat is adjusted.

I chose to bolt my seats directly through the floor-pan for strength and this leaves a gap under the base of the wood at the inside corners, which I stacked out with a nut and large washers. This gives the added benefit of the seats being bolted first to the wood, then through the floor-pan with the same bolt. The downside is the sealed floor-pan nuts will need removing should the seat need to come out in future. The alternative method, used by HSVTurbo in his build here, is to bolt the seats to a thicker metal bracket, then bolt the bracket through the wood and floor-pan. This way the seat can be removed from inside the car leaving the wood fixed in place, but I just don't feel this setup will be strong enough, even with the thicker metal bracket.

I used M10 nyloc-nuts with a dab of stud-lock inside and large-diameter [40mm] 'bumper' washers. A good blob of silicone-sealant was put between the washer and body, then round the outside of the seated nut. Finally, I coated them in a thick layer of Finnegan's WAXOYL Underbody Sealant, for protection obviously, but also to blend the shiny nuts and washers into the car's underside.

I still have the rear-seats, including the folding arm-rest, along with the door-cards/handles and rear trim-panels, so we'll have to see how much will fit after the MOT.

E21 316: Inner-Arch Fix + MOT Prep.

Hacking out the inner wheel-arches at the back to make the 16x9s fit left them in a right state, with a big gap up inside the wing. Being where it is, the gap is wide open to dirt and water flinging up off the wheel ready to rot the body from the inside out, so as a temporary measure I covered the area in ally-tape. It worked well, but was never going to last long. I figured the inner-arch would be considered a structural part of the body and would need a steel fillet welding in, but it doesn't appear to be the case so fibre-glass will do.

The area is a bit big for filling in though, so I shot up to Halfords and bought a square-metre of fibre-glass matting, £4.29. You need resin to apply it, which is a bit dearer. A kit is available for £9.99 that includes a small bottle of resin and a small mat, otherwise resin starts at a fiver and hardener is extra. The recommended resin is polyester-based, so it stretches, but I figure that marine epoxy-resin, which can be used for fibre-glass, will do the job as it may not be as flexible, but sure is waterproof and rock hard. I also happen to have a litre of the stuff left over from some carbon-fibre projects a few years ago.

I weighed the fibre-glass mat up to the whee-arch and cut it into rough shapes. The instructions say to coat the mat in resin and then stick it, but I found it just as easy and a little less messy to brush a little resin onto the surface, then stick the pieces of mat on dry and brush in heaps of resin over the top. The epoxy is quite thick and stiffens quickly, so this may the only workaround method using this stuff. It's certainly done the trick, the fibre-glass is as solid as the metal and has stuck well even to the rough under-seal surface, lets just hope it doesn't flex too much and crack away. It should see me through the MOT next week and that's the main thing, but at least there's no mud being flung up into the wing anymore. A quick coat of red-primer and the tester may not even notice the difference...