E21 316: Stretched Toyos first try + more spending.

Tried out the 8Js on the front with the new 195 Toyo T1Rs using 20mm spacers and there's a lot more room at the arch-lip now. The tyre doesn't catch at all turned hard-left, thought it would going over a bump. Hard-right the tyre is still catching the front valance slightly, but about 1cm cut away should be enough now and a little off the fender where it protrudes from the bumper - none of the bumper itself though. I had hoped to get away with smaller spacers on the front, but even with the 20mm spacers from the rear, the inside rim of the wheel is still 5mm inboard of the 15x7Js and there is not a lot of headroom.

I just haven't found time to try out the 9Js on the rear today as the valve is bust in one and on the other, about 6 inches of the bead has just been refusing to seat. My leg just couldn't take any more foot-pumping so I got hold of an air-compressor from a friend and took the tyre to nearly 90psi this morning, but it still wasn't having any of it. Eventually, after two goes deflating the tyre almost completely and trying to brush in soap between the tyre and rim, then taking it back up to about 65psi, the bead finally popped. The maximum pressure rating on the tyre is 50psi, though it says use no more than 40 to seat the bead, so it just goes to show that when the seal is tight enough it can take over twice that and still not seat. Bead-blaster machines can jet up to 200psi in one go and that doesn't even shred the tyre to bits so I'd be keen to know at what pressure a good new tyre would rupture at. Even so, always take the utmost care when inflating tyres past their rated pressures at home!

Apart from 4 new valve-cores (£2.99) and a valve removal-tool (£4.99) from Halfords, I've had to do yet more spending on parts as the project can't move on without them and I want to be getting somewhere near finished next weekend when we have the bank-holiday off. First up are adjustable camber-plates for the front, a must for style and it will likely give me a bit more room to play with before starting to cut. They're not approved for sale in the UK, so lets hope they make it here from Poland before the weekend - fingers crossed eh! Looking forward to these, though quite pricey @ £105 delivered, but whatever, they're the only ones of their kind. It's also time to stop digging my heels in and buy another set of spacers to go on the front, swapping the ones over from the rear is becoming a chore. I'd hoped to get some alloy ones to save hub weight, but again for easy access, the right centre-bore without more spigot-rings and to get the bolt-on kind I want, yep you guessed it, more steel ones. Another £59, oh well, roll on next weekend.

E21 316: Arch Rolling - First Test.

ET Plus complete arch-rolling kit was about £100 on eBay and comes with a full set of spigot rings to fir anything.

Hard to see in the pic, but quite a bit of scrubbing on the tyre and a faint red line all the way around the sidewall from the sharp-edged lip, below.

Rolling-tool bolts on to the hub, winds out against the arch and you're away, rolling it back and forth, winding it out a little more each time. This was insanely easy compared to what I was expecting. 

I managed to roll the sharp lip up almost flush and gave the rim of the arch a slight flare in about 15 minutes flat. No more scrubbage for now, even if the look hasn't changed much.

It's best to use a heat-gun to warm the paint so it doesn't crack, but without one to hand I figured hot water would do the trick. A bit of loose paint still flaked off from under the arch, but it looks like I'm already beginning to get rusty bubbles under the rim of all four arches and they will probably have erupted by summer. The n/s arch also consists of a fair bit of primer, so it'll be interesting to see how neatly that rolls out and I'll ask my paint guy how much smoothing and spraying all the arches will be with my left over paint. 

E21 316: Rear Wheel Spacers + Arch Rolling Kit!

With the engine now back in fine fettle [we hope!], I couldn't wait to get back on-project and spend a bit on stance, so I've started with these 20mm spacers for the rear wheels. I'm not sure if it's an illusion of the E21 body-shape, but the rear wheels always look a bit tapered in from the front ones, so these spacers should primarily even up the front/rear track or even bring the back wheels a bit further out than the front, as it should look. They'll also help make my rather skinny 7J wheels look a bit fatter and get the arch-clearance a bit tighter - and, of course, will make fitting fatter wheels [which is going to have to happen at some point isn't it] easier in the future.

In fear of the spacers pushing the wheel out too far and causing the outside of the tyre to contact the wheel arch, I also bought a wheel-arch rolling kit. It's about £100 to have a pair of arches rolled professionally and, as mine is a work-in-progress and I'm not 100% on the setup I'll be using, I decided £97 for my own kit will definitely work out cheaper if I need to keep on rolling them out as I go lower and wider...

French made spacers are nicely machined, but billet steel and pretty heavy.

Deemed too wide for extra-long wheel-bolts, these babies have two sets of holes and bolt on to the hub by themselves.

Rear wheels slightly proud of front ones as they should be, but a slight loss of negative-camber.